Glossary · 22 terms
Injection pen terms, defined precisely
Every term below is one we actually use in quotations, inspection reports and supplier discussions. Where a word has a loose everyday meaning and a tight engineering meaning, the tight one is what is written here.
Device & mechanism
- ISO 11608
- The international standard series for needle-based injection systems for medical use. ISO 11608-1 covers pen injectors and specifies requirements and test methods for dose accuracy, durability and mechanical performance.
- Injection force
- The thumb force a patient must apply to deliver the dose. It rises with formulation viscosity and falls with larger needle bore, and it is a primary driver of hand pain and dose-completion errors in patients with limited grip strength.
- Break-loose and glide force
- Two measures of stopper movement inside a cartridge. Break-loose force is the peak needed to start motion from rest; glide force is what is needed to sustain it. Both are affected by siliconisation and stopper geometry.
- Dial torque / rotational damping
- Rotational resistance felt while dialling a dose. Controlled damping prevents accidental over-dialling and under-dialling, and makes detent clicks feel consistent; it is set by the fit of the damping ring and the detent geometry.
- End-of-dose click
- An audible and tactile signal confirming the dial has returned to zero and the dose is complete. It is a usability requirement in most pen designs because patients otherwise tend to stop pushing early.
- 3 mL cartridge
- A standard multi-dose glass container with a rubber stopper and aluminium crimp cap, sized under ISO 13926-1. Its bore diameter and length fix the pen interface, so a pen platform is designed around a cartridge family rather than a single part number.
- Pen needle gauge
- Wire diameter of a pen needle, where a higher gauge number means a thinner needle: 31G is roughly 0.25 mm outer diameter and 32G roughly 0.23 mm. Thinner needles reduce pain but raise injection force and can lengthen delivery time.
Dose & accuracy
- Dose increment
- The smallest dose step a pen can be dialled to, for example 0.01 mL or one insulin unit per click. Increment size determines titration granularity: smaller steps allow finer adjustment but require more dial turns to reach a large dose.
- Minimum deliverable dose
- The smallest volume a pen can reliably deliver within its stated accuracy tolerance. It is bounded by lead-screw pitch, dial resolution and cartridge bore, and it matters most for paediatric, growth hormone and micro-dose titration programs.
- Dose accuracy
- How closely the volume actually delivered matches the volume dialled, expressed as a percentage or absolute deviation across the full dial range. ISO 11608-1 testing samples minimum, mid-range and maximum doses across multiple units and lots.
- Priming (air shot)
- A small dose dialled and dispensed before the first injection to remove air from the cartridge and confirm the needle is patent. Priming volume is a design parameter of the pen and an instruction item in the user manual.
Manufacturing & tooling
- T0 / T1 / T2 samples
- Successive tooling trial rounds. T0 is the first shot from a new mould, T1 and T2 follow dimensional correction to core and cavity steel. Buyers typically approve functional samples at T1 and freeze design at T2.
- DFM review
- Design for manufacturability: a structured review of wall thickness, draft angles, gate placement, tolerances and assembly sequence before steel is cut. Catching an issue at DFM costs a drawing change; catching it after tooling costs a mould rework.
- IQ / OQ / PQ
- Three-stage process validation. Installation qualification confirms equipment is installed as specified, operational qualification confirms it works across its operating range, and performance qualification confirms it produces conforming product routinely.
- OEM vs ODM
- In OEM the buyer owns the design and the factory manufactures to it. In ODM the factory owns an existing platform that the buyer configures — colour, logo, dose scale, packaging. ODM on an existing mould is faster and cheaper than new tooling.
- Cleanroom class (ISO 8 / Class 100,000)
- Air cleanliness classification by particle count per cubic metre. ISO 8 corresponds to the older US Federal Standard 209E "Class 100,000" and is the common level for pen injector assembly; ISO 7 ("Class 10,000") is used where bioburden control is tighter.
Regulatory & quality
- ISO 13485
- The quality management system standard for medical device organisations. It governs design control, purchasing, production, traceability, CAPA and record retention; certification is issued by a notified or accredited body against a defined scope.
- CE marking under EU MDR
- The conformity route for placing a device on the EU market under Regulation (EU) 2017/745. Class IIa and above generally require a notified body, and the certificate names both the manufacturer and the device scope it covers.
- 510(k) vs DMF
- A 510(k) is a premarket notification demonstrating substantial equivalence for a finished device. A Drug Master File is a confidential submission supporting a drug application. A device component supplier may hold neither on its own.
- MDSAP
- Medical Device Single Audit Program: one audit covering ISO 13485 plus the regulatory requirements of participating markets (US, Canada, Brazil, Japan, Australia). It reduces duplicate inspections but does not replace market authorisation.
- Freedom to operate (FTO)
- A legal analysis concluding that making, using or selling a product does not infringe third-party patents in a given market. For pen injectors it usually focuses on dose mechanisms, and it is separate from owning your own patents.
- NMPA Class II filing
- China’s registration tier for medium-risk medical devices, administered by NMPA and provincial authorities. Class II devices require registration plus a production licence; operating filings apply to distribution activity rather than to the device itself.
Browse the topic clusters
Each cluster collects the articles that use these definitions in a real program decision.
- Sourcing & supplier evaluationHow to shortlist, audit and compare injection pen manufacturers before you commit tooling money.7 articles
- GLP-1 & peptide device programsDevice-side requirements for titration scales, multi-dose peptide programs and clinic channels.5 articles
- Device design & dose accuracyMechanism-level engineering: damping, dial torque, injection force and how accuracy is measured.5 articles
- OEM manufacturing & toolingMould development, T0–T2 sampling, cleanroom assembly, and packaging/branding configuration.3 articles
- Regulatory, quality & factory visitsFDA/CE/ISO expectations, documentation packages, and what buyers learn on a real factory visit.4 articles
Manufacturer guide
The definitions are the starting point. See them inside the real sequence: tooling, sampling, inspection gates and the document package.